Baby Cribs Safety Tips

Crib Design

Dispose of antique baby cribs with decorative cutouts, corner posts or lead paint. The space between the slats should be no more than 2-3/8 inches apart to prevent infants from getting their head stuck between them. Cribs manufactured after 1974 must meet this and other strict safety standards. The corner posts should be the same height as the end panels or less than 1/16 of an inch higher than the end panels.

No cut-out areas on the headboard or foot board so a baby’s head cannot get trapped. The top rails of crib sides, in their raised position, should be at least 26 inches above the top of the mattress support at its lowest position.

As soon as the child can pull himself to a standing position, set and keep the mattress at its lowest position. Stop using the crib once the height of the top rails is less than three-fourths of the child’s height.

Mattress

The mattress should fit snugly next to the crib so that there is no gap. If two adult fingers can be placed between the mattress and the crib, the mattress should be immediately replaced. Do not use plastic packaging materials, such as dry cleaning bags, as mattress covers. Plastic film can cling to children’s faces and should never be in or near the crib.

Put your baby to sleep on his or her back or side in a crib with a firm, flat mattress and no soft bedding underneath. Talk to your pediatrician about which sleeping position is best for you child.

Crib Hardware

The drop side(s) of the crib should require two distinct actions or a minimum force of ten pounds with one action to release the latch or the locks to prevent accidental release by the child.

The crib hardware should be checked for disengaged, broken, bent or loose pieces. Special checks should be made of the mattress support hangers and brackets so they cannot drop. The hardware and the crib should be smooth and free of sharp edges, points and rough surfaces.

Crib Accessories

Bumper pads should cover the entire inside perimeter of the crib and tie or snap in place. Bumper pads should have at least six straps or ties and any excess length of straps or ties should be cut off. Bumper pads should never be used in lieu of proper spacing between the slats and should be removed from the crib as soon as the child can pull himself to a standing position.

Teething rails that are damaged should be fixed, replaced or removed immediately. To prevent possible entanglement, mobiles and crib gyms, which are meant to be hung over or across the crib, should be removed when the child is five months old or when he begins to push up onto hands and knees or can pull himself up. Keep the crib clear of plastic sheets, pillows, and large stuffed animals or toys. These can be suffocation hazards or can enable youngsters to climb out of the crib. Any cloth or vinyl items that are loose or torn should be replaced or repaired immediately.

Crib Environment

Do not place crib next to a window. Drapery and blind cords pose an entanglement hazard and window screens are not intended to keep a child in, only insects out. Install smoke detectors. Follow the manufacturer’s directions for placement. Check at least once a month to make sure battery and smoke detector are in good working condition.

If you are reading this article, you are probably wondernig, why and how do you build a computer. Building your own computer is more simple than you think and has many benefits.

Why Build A Computer?
Building a computer has many benefits over buying a premade. First of all, it is generally cheaper if you build your own than buying one. If you shop your components, your DIY(Do it yourself) computer will be cheaper than its premade equivalent. If you build your own computer, it will be faster than one that is premade, because most computer manufacturers use cheap components and try to cut corners to cut down costs. Additionally, your self built computer has more room to upgrade if you so decide to in the future. Prebuilt computers usually only have enough expansion slots for the components that are going to be in the computer. Because of this, your prebuilt computer will become obsolete sooner. Also, building a computer is a satisfying experience and you will learn more about how your computer works.

How do I go About Building a Computer?
Building a computer is probably much simpler than you think. Especially now, things have been simplified and standardized. First, you pick out components and make sure they are all compatible. Once you get the parts, you put them together! This guide was made to show you how to do everything and contains pictures and good information to make building a computer a fun and rewarding experience. For more information about building a computer, be sure to check out the next article in this guide!

In the world of home ink jet color printing, there is some confusion concerning CMYK color and RGB color. Many photo enthusiasts don’t realize what kind of color space their digital cameras output and are confused when it comes to printing images off of their home ink jet printers. They hit print and wonder why the printed image looks different from what they see on their monitor.

CMYK is the color description representing printed material, short for the colors Cyan, Magenta, Yellow, and Black. Mixing these 4 colors together in different amounts give you the millions of colors that reproduce the colors in printed material. These are actual inks used in printing the images you see in color magazines and books. RGB is the color description for images viewed on your computer monitors, short for Red, Green, and Blue. RGB color is actually light, and mixing different levels of these light colors
creates the millions of colors that come from your computer monitor. All websites and nearly everything you see on your computer monitor is RGB unless the images have been converted to the CMYK color space.

When you print your images on your ink jet printer from your computer, your printer prints the image using CMYK inks. Viewing your image in RGB and then printing it out in CMYK may not yield the results you want. Programs such as Adobe Photoshop will convert your image from RGB to CMYK or vice versa. Some printers require the image to be CMYK before you can print the image correctly. Some printers don’t print the image correctly if the image being printed is in RGB space.

A good reason for printing with a CMYK image is to see your image in CMYK color before printing. When an image is converted to CMYK from RGB, there may be some color changes that are noticeable in the image. The reason for this is because many colors in RGB cannot be reproduced using CMYK inks. That is why it is always a good idea to convert your image to a CMYK color space before printing. You could notice significant color changes to your image, especially in the very intense color areas of your image. Some of these intense color areas may appear less intense or very dull once converted. With photo editing software, you can go in and fix these trouble color areas to your liking.

Many ink jet printers on the market today actually print directly from an RGB color image. And converting the image to CMYK may cause it to print incorrectly. You will need to determine what color space your ink jet printer supports. The packaged software usually will give you a hint regarding color spaces. If there is no option to convert the color space from RGB to CMYK, most likely, the printer will print directly from an RGB color source. Usually, the higher end ink jet printers deal with the CMYK color space as consumer level enthusiasts don’t even know these color spaces exist. New higher end ink jet printers, however, are now printing directly from the RGB color space as there is a wider spectrum of color that can be reproduced in RGB compared to CMYK color.

If you visit the website, Instantimagers.com, the ‘Framers’ and ‘DVD Cover & Disc Art’ designs are provided in both RGB and CMYK color spaces. Comparing the RGB and CMYK images side by side, you’ll notice there are color differences. This is due to some RGB colors not being available as a CMYK converted color. Both versions are provided because not all printers are alike. Some tend to print better with one color space. Many of CMYK printed designs have been manipulated further after conversion to match more closely the colors from the RGB color space as many of the colors in some designs did not covert seamlessly.

If all this seems confusing, not to worry. The key thing to remember is to print using RGB color if your printer and software support it. Let the software and the printer worry about getting the colors right. If you are more experienced with photo color correction and want more control over the color of the image, print in CMYK. You’ll actually be manipulating and printing the image in the color space your ink jet printer’s inks are using. You will be able to see the limits of the CMYK printing color spectrum right on your monitor. Getting color right with RGB and CMYK is totally different from calibrating your printer to match the colors on your monitor. That is actually the second step in getting the best color out of your prints. Understanding the difference between RGB and CMYK is the first step in getting the best print outs on your home ink jet printer.